Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
We have found the article relating to Installing A Bathtub below on the internet and thought it made perfect sense to share it with you over here.
Installing a bathtub isn't specifically brain surgery, but it does need solid plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately hard project. If the old bathtub is conveniently available, the task can move immediately; if you need to open up a wall surface to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This short article will certainly help you mount a brand-new tub in your bathroom if you have actually already bought a brand-new tub as well as do not require to alter the arrangement of your previous water system pipelines.
Your tools as well as product list need to comprise the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to avoid pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are valuable in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the tub up until the spirit level reads degree.
To mount taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water as well as check all joints and brand-new pipework for leaks as well as tighten them if required. Fill the tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous type should be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with wetness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on A Step-by-Step Guide to Installing a Bathtub, I thought sharing that information was smart. Appreciated our content? Please share it. Let other people find it. We enjoy reading our article about How to Install a Bathtub.
Quick service, just dial! Report this page